Top 9 L298N Dual H-Bridge Motor Controller – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. MELIFE

#ad

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
MELIFE #ad - External size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove.

If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits. Double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient. Main driver chip l298n, strong anti-interference, low calorific value, afterflow diode protection, strong driving ability, more stable and reliable for Arduino projects. No assembly required. This l298n board comes ready to go. Just wire up motors and power, easy to use.
BrandMELIFE #ad
ManufacturerMELIFE #ad
Part Number15489

2. Generic

#ad

2Pack L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Compatible with Ar-duino Electric Projects, Smart Car Robot

#ad
Generic #ad - Large capacity filter capacitance, afterflow protection diode, more stable and reliable. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability.

To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Dual-channel h-bridge driver working mode creates higher working efficiency, Can drive one 2-phase stepper motor, L298N as main chip, one 4-phase stepper motor or two DC motors. High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w.
BrandGeneric #ad
ManufacturerDoes Not Apply #ad
Part NumberNA
ModelNA

3. TIMESETL

#ad

TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

#ad
TIMESETL #ad - Just wire up motors and power, easy to use. Easy to use no assembly required. High quality main driver chip l298n, afterflow diode protection, low calorific value, strong driving ability, strong anti-interference, more stable and reliable for Arduino projects.

Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. This l298n board comes ready to go. High efficient double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
BrandTIMESETL #ad
ManufacturerTIMESETL #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberTXJ-061-EU
ModelL298N motor controller

4. DAOKI

#ad

DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
DAOKI #ad - Package included - 5 pcs L298N Motor Driver Controller Board Modules. The signal is shown in the figure. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. The connecting method is shown inbelow figure after enable ENA ENB.
BrandDAOKI #ad
ManufacturerDAOKI #ad
Part NumberFBA_TS-US-078-SNL
ModelFBA_TS-US-078-SNL

5. ACEIRMC

#ad

Organizer 5pcs L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Controller Board

#ad
ACEIRMC #ad - 2. The chip manual proposes to support 35v, for example, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, the motor with a rated voltage of 18V shall be driven.

This l298n board comes ready to go. Double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient. 5. Just wire up motors and power, easy to use. 1. When you are driving voltage above logo for the 12 v input, can make to onboard power supply 5 v logic, interface of + 5 v The power supply does not input voltage, when using the onboard after 5 v power supply, can actually accept input range is 7 to 12 v for 7 v to 12 v, but can yield 5V voltage for external use.4

4. No assembly required. 3. Great for for arduino diy smart car robot power uno mega r3 mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
BrandACEIRMC #ad
ManufacturerOrganizer #ad
Part Number10544

6. Generic

#ad

5Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Compatible with Ar-duino Electric Projects, Smart Car Robot

#ad
Generic #ad - To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.

Large capacity filter capacitance, afterflow protection diode, more stable and reliable. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Dual-channel h-bridge driver working mode creates higher working efficiency, Can drive one 2-phase stepper motor, L298N as main chip, one 4-phase stepper motor or two DC motors. High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w.
BrandGeneric #ad
ManufacturerDoes Not Apply #ad
Part NumberNA
ModelNA

7. KeeYees

#ad

KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino

#ad
KeeYees #ad - Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.

This is a good parts kit for an arduino and raspberry pi based RC car project. It has the strong driving ability, low calorific value and strong anti-interference ability. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage. Motor drive controller: l298n used as the main driver chip.
BrandKeeYees #ad
ManufacturerKeeYees #ad

8. PChero

#ad

PChero L298N Motor Drive Controller Board Module, Dual H Bridge DC Stepper For Arduino Smart Car Robot

#ad
PChero #ad - This l298n board comes ready to go. Drive voltage 5v-35v, high working power to 46v. Package included - 1pcs L298N Motor Driver Controller Board Modules. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module.

Power to 25w. Note: to avoid damage, please use an external 5V logic supply when using more than 12V driving voltage. Easy of use - no assembly required. High quality - use l298n as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value.

High efficiency - dual-channel h-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. Just wire up motors and power, this thing will work wonders. Item size - external size 43*43*27mm / 1. 69*1. 69*1. 06 inch. Large current can reach 3A MAX and continue current is 2A.
BrandPChero #ad
ManufacturerPChero #ad
Part NumberiS017*1

9. DollaTek

#ad

DollaTek Mini Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC Stepper for Arduino Smart Car Robot

#ad
DollaTek #ad - Logic voltage 5v. Driving voltage 5v-35v 2a current unit max single bridge. Maximum storage power temperature 25W: -25 ~ +130 Size: 43 * 43 * 27mm / 1. 69 * 1. 69 * 1. 06 ". The module uses st l298n chipset, has strong driver capability, afterglow protection diode, more stable and reliable. Dual-channel H-bridge driver operation mode creates greater working efficiency. To avoid damaging the voltage chip stabilization, please use external 5V logic power supply when using more than 12V drive voltage.
BrandDollaTek #ad
ManufacturerDollaTek #ad