DEVMO#ad - Voltage indication of motor driver output end; can solder heat sink;. Isolated chip 5v power supply can be shared with the MCU 5V, can also use the on-board 5V supply; the supply voltage 5. 5v to 27V. Double bts7960 h-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A.
KEYESTUDIO#ad - Easy to install on your rpi board. Standard raspberry pi 40pin gpio extension header, supports Raspberry Pi series boards like Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+/4B and later versions.
Please note raspberry Pi board, 4 xM2. 5*10mm copper pillars, remote control and motors in the photos are Not Included! . Reserved i2c spi control pins, allows to work with other control boards and sensors.
This motor driver hat gives your raspberry Pi the ability to drive two DC motors, with drive current up to 2A. Logic part input voltage: 5v ; Driving part input voltage: 4. 8 ~ 24v ;. Included 4x m2. 5*20mm screws, 4x m2. 5 nuts. Comes with an IR receiver for communication with an infrared remote controller.
JUN-ELECTRON#ad - The built-in 78m05 chip works by partially taking power from the drive power supply. Provide high-quality products and services, simple to use, including operation tutorials.
Widely application : the module is very suitable for DIY design car project, 3D printer, learning programming. The l298n used in this module is used as the driver chip, which has the characteristics of strong driving ability, low heat generation and strong anti-interference ability.
The module consists of an l298 motor driver IC and a 78M05 5V regulator. It uses an h-bridge to easily control the direction and speed of up to 2 DC motors. This l298n motor driver module is a high power motor driver module for driving dc and Stepper Motors. If working with a drive voltage greater than 12V, please connect the external 5V logic power supply.
Kiro&Seeu#ad - Double bts7960b large current 43A H bridge driver. Voltage indication of motor driver output end, can solder heat sink. Double bts7960b h-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver.
Bicool#ad - Motor driver: TB6612FNG. Standard raspberry pi 40pin GPIO extension header, supports Raspberry Pi series boards. Logic voltage: 3. 3v. Onboard pca9685 chip, high efficiency, provides 12-bit hardware PWM to adjust motor speed.
Onboard tb6612fng dual H-bridge motor driver, low heating. Reserved i2c control pins, up to 3A output current, wiringPi, allows to work with other control boards.
Pwm driver: PCA9685. Power supply: 6v~12v vin terminal. Comes with development resources and manual examples in BCM2835, and python. I2c controlled, by setting 5 address jumpers, it is stackable up to 32 this modules. Integrates 5v regulator, can be powered from battery through vin terminal. Control interface: I2C.
OSOYOO#ad - Usb port gives stable 5V/2. 4a output. Osoyoo model-pi l298n board is perfect motor driver board for Raspberry Pi portable applications such as robots, drones, RC cars, mini weather station etc.
This board supports all the features of l298n dc motor driver, in addition, it also has a USB 5V output port which can provide stable voltage to Raspberry Pi board without AC power input.
Each channel supports two sockets which can power two DC motors. It also has two channels of PWM output. I/o pins fully compatible with l298n including enablea/in1/in2/in3/IN4/EnableB. Input power source can be 7. 5v-24v batteries we suggest using 2pcs tandem 18650 batteries etc, or 6pcs AAA Tandem AAA batteries, or, 2pcs Parallel 9V batteries for robot project.
Zopsc-1#ad - Reserve the i2c control interface to facilitate the connection with other main control boards. Onboard pca9685 chip, can output 12-bit hardware to PWM control motor speed. Based on raspberry pi interface design, suitable for Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+.
Yoidesu#ad - Based on raspberry pi interface design, suitable for Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+. Onboard pca9685 chip, can output 12 bit hardware to PWM control motor speed. Reserve the i2c control interface to facilitate the connection with other main control boards.
Liadance#ad - Stable: motor drive controller board use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Parameters: high working power to 35v, large current can reach 3A MAX and continue current is 2A, power to 25w.
High efficiency: Dual-channel H-bridge driver working mode creates higher working efficiency. Safe: large capacity filter capacitance, aftelow protection diode, more stable and reliable. Function: l298n as main chip; can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.