Top 10 OLED Display Arduino – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. IZOKEE

#ad

Yellow-Blue-IIC, IZOKEE 0.96'' I2C IIC 12864 128X64 Pixel OLED LCD Display Shield Board Module SSD1306 Chip 4 Pin for Arduino for Raspberry Pi Pack of 3pcs

#ad
IZOKEE #ad - Due to the high resolution of 128 x 64 pixels, stm32 / 2, msp430 series, the display offers a lot of space to display elements! Easy connection of the display with arduino, CSR IC, 51 Series, raspberry pi, etc.

096" ssd1306 128x64 oled lcd display with iic/i2C Interface-4PIN. The iic address can be changed. The yellow area is the upper row, and the lower area is blue, as shown in the picture. Only through I2C interface via four pins! Thanks to the standard driver chip ssd 1306 libraries already exist for Arduino, Raspberry Pi and 51 Series, which makes programming very easy! Tip: the blue and yellow areas are fixed and cannot be reset.
BrandIZOKEE #ad
ManufacturerIZOKEE #ad
Weight45 Grams
Part NumberIZKE31-IIC-YB-3
ModelIZKE31-IIC-YB-3

2. GoldenMorning

#ad

2pcs 0.96 Inch OLED Display Module IIC I2C SSD1306 Compatible with Arduino Driver DC 3-5V White

#ad
GoldenMorning #ad - The default value of IIC address is 0x3c. 096 inch oled with white/blue/yellow&blue color, 128x64 resolution. It is highlight. It is full viewing angle and wide operating temperature. Supported voltage: 3V-5V DC. The driver ic is ssd1306 with I2C interface. It is oled display without backlight and it is low power dissipation. The thickness of galss is only 1. 4mm. We have the datasheet of display. It is specification, driver IC, driver code and connection of the hardware. We also have the technical support.
BrandGoldenMorning #ad
ManufacturerGoldenMorning #ad
Height1.97 Inches
Length2.56 Inches
Width2.64 Inches

3. waveshare

#ad

Waveshare 1.5inch RGB OLED Display Module 128x128 Pixels 16-bit High Color 65K Colors with Embedded Controller Communicating via SPI Interface.

#ad
waveshare #ad - Supports 4-wire spi or 3-wire SPI interface, configured via onboard resistor. 128x128 high resolution, 65K colors, clearly displays colorful images. Comes with development resources and manual examples for Raspberry Pi/Jetson Nano/STM32. Display color: RGB, 65K colors. This is a general rgb oled display module, with embedded controller, 1. 5inch diagonal, 16-bit high color 65K colors, 128x128 pixels, communicating via SPI interface.
Brandwaveshare #ad
ManufacturerWaveshare #ad
Weight0.04 Pounds
Part Number1.5inch RGB OLED Module
Model1.5inch RGB OLED Module

4. MakerFocus

#ad

MakerFocus 2pcs I2C OLED Display Module 0.91 Inch I2C SSD1306 OLED Display Module White I2C OLED Screen Driver DC 3.3V~5V for Arduino

#ad
MakerFocus #ad - Please do not buy shenzhen jinmao electronics co. Please look for the makerfocus brand, we are not authorized to them, please do not be fooled! Please feel free to email us if you have any questions, there is only one module in their packaging, Ltd.

We will help you to resolve it asap. The display performance is better than the traditional LCD display, also lower consumption; SSD 1306 oled display; I2C oled display, IIC I2C communications simplifies connections;. Product manual: https://drive. Google. Com/open?id=14a_lufwqvzaku-PKTfJdWmUZ4T4Wk65X.

Use with arduino, stm32, esp32, esp8266, etc; 3.35v power; operating temperature:-40 - 85 ℃. How to email us? plz click “makerfocus” and click “Ask a question” to email us! Looking for your consultation!128x32 oled display, self-illumination, no need backlight, Display Color: White. Plz note: these i2c olED Display Modules come without pin headers.
BrandMakerFocus #ad
ManufacturerMakerFocus #ad
Height0.39 Inches
Length1.5 Inches
Weight0.02 Pounds
Width2.76 Inches
Part Number20200330-SD8V
Model8541549353

5. GoldenMorning

#ad

2 pcs 1.3" SPI Serial 128x64 SSD1306 OLED LCD Display LCD Module for Arduino AVR PIC STM32 7P-SPI, Blue

#ad
GoldenMorning #ad - It is oled display without backlight and it is low power dissipation. The thickness of galss is only 1. 4mm. It is highlight. It is full viewing angle and wide operating temperature. We have the datasheet of them. It is specification, driver IC, driver code and connection of the haedware. We have the technical support. The driver ic is ssd1306 with SPI interface, not SH1106. Supports many control chip:fully compatible with Arduino 51 series, msp430 series, stm32/2 CSR IC etc. 1. 3 inch oled with blue, and 128x64 resolution.
BrandGoldenMorning #ad
ManufacturerGoldenMorning #ad

6. GeeekPi

#ad

Raspberry Pi,Beagle Bone Black, GeeekPi 5PCS 0.96 Inch OLED Module 12864 128x64 White SSD1306 Driver IIC Serial Display Board Module for Arduino

#ad
GeeekPi #ad - It has super high contrast, user can create the fonts through the font generation software. Parameter:resolution: 128 x 64, view angle: > 160°, support voltage: 3. 3v-5v dc, full screen lit 008w, power consumption: 004w during normal operation, Color:White.

128 x 64 pixels:needn't backlight, even tiny fonts quite readable. No embedded fonts inside the OLED controller, bright and crisp dots, the display unit can self-luminous. Changeable iic address:the iic address can be changed, it is convenient to use with different machines Four square holes are easy to install.

Showing graphical & textual information directly on your micro-controller projects. Wiki:https://wiki. 52pi. Com/index. Php/096_inch_oled_module_sku:_S-0005 ; https://youtu. Be/t1n9xyrc1GQ. Compatible with many control chips: raspberry pi 4b/3b+/3b/2b/zero, 51 mcu, Beagle Bone Black, arduino UNO and Mega, STIM 32 and so on.
BrandGeeekPi #ad
ManufacturerGeeekPi #ad
Part NumberS-0005-5Pack

7. ELEGOO

#ad

ELEGOO UNO R3 2.8 Inches TFT Touch Screen with SD Card Socket w/All Technical Data in CD for Arduino UNO R3

#ad
ELEGOO #ad - With touch pen inside, you can use it more easily. 8 inches colorful display lcd screen. 2. Not including the uno R3 controller board and usb cable. With technical data. We have always cared about the customer experience and improve the product function details. Free tutorial in cd, better price, better service.
BrandELEGOO #ad
ManufacturerELEGOO #ad
Height1.18 Inches
Length3.54 Inches
Weight0.11 Pounds
Width3.94 Inches
Part NumberEL-SM-004
ModelEL-SM-004

8. DEVMO

#ad

DEVMO 2.2 Inch ILI9341 SPI TFT LCD Display 240x320 ILI9341 LCD Screen with SD Card Slot Compatible with Arduino Raspberry Pi 51/AVR/STM32/ARM/PIC

#ad
DEVMO #ad - Support serial spi mode, interface 4-Wire SPI, Need 4 IOs from your MCU only. Support a variety of microcontroller IO connection, professional and practical. 5v compatible, use with 3. 3v or 5V logic. Durable hard pcb board and SD card socket, ideal for 5110 interface. 2. 4 inch tft lcd shield without touch panel, fast to operate.
BrandDEVMO #ad
ManufacturerDEVMO #ad

9. WINGONEER

#ad

Yellow Blue Font, WINGONEER 2Pcs 0.96 Inch I2C IIC SPI Serial 128x64 OLED Display SSD1306 Module Board with Pin Headers

#ad
WINGONEER #ad - Dot matrix size: 128x64. Display: 096" oled Display. Controller ic: SSD1306. Working voltage: dC 3. 3v - 5V. Dimension: 29. 3 x 27. 6mm.
BrandWINGONEER #ad
ManufacturerWINGONEER #ad
Part Number1

10. diymore

#ad

Diymore 2.42" OLED Digital IIC I2C SPI Serial 12864 128X64 Pixel LCD Screen Display Module SSD1309 for Arduino C51 STM32 DIY Electronic White

#ad
diymore #ad - The driver chip for this screen is ssd1309, which supports 4-wire SPI, I2C and 8-bit interfaces. Interface selection: spifactory setting or IICYou need to move the resistor R4 to R3, and solder R5 with 0 ohm resistor. It does not support 3-wire SPI. Diagonal screen Size: 2. 42 inch. Resolution: 128 * 64. Driver ic: ssd1309.
Branddiymore #ad
Manufacturerdiymore #ad
Part Number030526242
Model030526